×

lkk

Price: 0 € - 100 €

FORGOT YOUR DETAILS?

Integrated TEHNOLINK Load Bank

Integrated TEHNOLINK Load Bank

TEHNOLINK offers a Load Bank models that are robust, broad-spectrum power (50kW¸1000kW) at nominal voltage and specifically designed to work within the framework of the diesel engine. ITLB (Integrated TEHNOLINK Load Bank) sets high standards with intelligent control management, high protective measures, adjustable step loads and effortless installation.

ITLB is an excellent economical solution for regular testing carried out in order to check the work of the diesel engine as well as during the critical commissioning them. Load Bank is a device that represents a continuous power source and the load at which all the energy received from the source dissipates tj.rasipa. Load obtained by this type Load Bank-a fully active ie. cosf = 1 so if your needs are different, it is necessary to consider the other model-a TLB (TEHNOLINK Load Bank). The role of a Load Bank is presented in the form of support during operation, testing and protection of the power supply. Application of Load Bank's impossible to WET STACK-ING engine or phenomena that occur when unburned fuel due to a light load preserve engine performance as part of the genset drive is certainly an imperative.

Integrated TEHNOLINK Load Bank is a completely innovative and economical solution with effortless installation in the extension part of the exhaust unit. The need for additional fan in this design because there is a very strong radiator that is already resistant to the engine as part of the drive unit.

  • The waterproof construction (degree of protection IP23)
  • Designed for continuous operation without the need for a cool-down period
  • The resistor elements are very well insulated ceramic rod on which are wound and protected by fuses
  • Intelligent protection solutions, indications of problems and operational control
  • The ultimate economic solution during temporary testing

Cabinet construction

The construction of the cabinet ITLB-a is produced from galvanized steel with a very high quality of the final painting and external covers made of stainless steel. The enclosure is OPEN FRAME type, and is intended for mounting in the extension part of the drive power unit to cool completely heaters were provided. Within each box with its lateral side are:

  • Consumer connections
  • Load-Step contactors
  • Control elements
  • Fuses

Disposition of a resistive elements are assigned in a very precise of winding method which provides flow of air to a greater occurrence and to minimize overheating. All resistive elements are wound very well insulated ceramic barrier that prevents short circuits between the radiators.

Remote control and alarms

  • Air-Flow control
  • Over-Temperature
  • Load Dump
  • Automatic Load Dump

COOLING SYSTEM

Cooling system of  Integrated TEHNOLINK Load Bank type of resistive elements constitutes a refrigerator that is located within the drive work unit. The amount of intake air must always be prepared to meet the needs of heaters in order not to cause breakdown.

LOAD BANK PROTECTION

Within each TLB is EMERGENCY STOP that allows the user at any time to terminate the operation of Load Bank-a in a case of unforeseen situations. Protective elements that are part of the distribution box provide adequate protection to possible short circuit. Visual indication of the distribution cabinet Load Bank in unforeseen situations (Motor Overload, Air-Flow failure, Over-Temperature) prevents the user to manually start the Load Bank's.

CONTROL MODUL

  • Emergency stop (E-STOP)
  • Main switch On/Off
  • Individual Load Step ON/OFF switch
  • Fault condition indicators (indication of contingencies)
  • Normal Condition indicators

AUTOMATIC LOAD DUMP

If the Load Bank is connected in parallel with the network and then the engine via a current transformer observe how the load aggregate and depending on its value does not allow that the unit is loaded with less than 40%. Automatic Load controller represents a sophisticated controller that adds and subtracts genset load depending on its current term exposure and all in order to preserve engine performance as part of the genset drive power due to light load. The controller adds a load in specified increments  steps depending on Load Bank's  power.

The consequences of non-use TEHNOLINK Load Bank

  • Unburned fuel promotes the destruction of the engine block
  • Excessive oil consumption
  • Reduced efficiency and motor power
  • Reduced output power generator
  • Increased emissions
  • Early repair of the engine block
  • Increased maintenance costs of the engine block

Application of TehnoLink Load Bank-a

  • UPS systems
  • Diesel Generators
  • Plane power generators
  • Wind generators
  • Hydro generators
  • Energy recuperations

In the modern world where a temporary or permanent interruption of power represents a major economic loss or liabilities and needs of each facility, factory or office is certainly the existence of the reserve power supply. TEHNOLINK genset emerge as the ultimate solution. As  currently the only domestic manufacturers of diesel genset as well as the quality of our production and reliability of their work is imperative. In order to offer our customers additional support gensets, our team of experts presents a modern solution for protection of diesel generators. PTLB (TEHNOLINK Portable Load Bank) is a completely innovative and superior solution to the problem of light load diesel engines. As we do not want to allow our customers light load of genset in any part of the day occur much bigger problems with the drive motor, we offer a solution that will impose a load  at least 40% of nominal at a time when it is needed. The constant progress, innovative ideas and cutting edge technical solutions represents constant goal of all  TEHNOLINK workers so if you want a secure income and peace of mind, please contact us.

TOP